document number: 83384 for technical questions, contact: esdprotection@vishay.com www.vishay.com rev. 1.0, 18-apr-11 1 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 4-line bus-port esd-protection VBUS54DD-HS4 vishay semiconductors marking (example only) dot = pin 1 marking x = date code y = type code (see table below) features ? ultra compact llp1010-6m package ? low package height < 0.4 mm ? 4-line usb esd-protection ? low leakage current ? low load capacitance c d = 0.8 pf ? esd-protection acc. iec 61000-4-2 15 kv contact discharge 15 kv air discharge ? pin plating nipdau (e4) no whisker growth ? compliant to rohs directive 2002/95/ec and in accordance to weee 2002/96/ec 20896 20897 1 5 4 2 3 6 20932 xy ordering information device name ordering co de taped units per reel minimum order quantity VBUS54DD-HS4 VBUS54DD-HS4-g4-08 5000 (8 mm tape on 7" reel) 5000 package data device name package name type code weight molding compound flammability rating moisture sensitivity level soldering conditions VBUS54DD-HS4 llp1010-6m d 1.07 mg ul 94 v-0 msl level 1 (according j-std-020) 260 c/10 s at terminals absolute maximum ratings parameter test conditions symbol value unit peak pulse current pin 1, 3, 4 or 5 to pin 2 or 6 acc. iec 61000-4-5; t p = 8/20 s/single shot i ppm 3a peak pulse power pin 1, 3, 4 or 5 to pin 2 or 6 acc. iec 61000-4-5, 8/20 s/single shot p pp 57 w esd immunity contact discharge acc. iec 61000-4-2; 10 pulses v esd 15 kv air discharge acc. iec 61000-4-2; 10 pulses 15 kv operating temperature junction temperature t j - 40 to + 125 c storage temperature t stg - 55 to + 150 c ** please see document vishay material category policy: www.vishay.com/doc?99902
www.vishay.com for technical questions, contact: esdprotection@vishay.com document number: 83384 2 rev. 1.0, 18-apr-11 this document is subject to change without notice. the products described herein and this document ar e subject to specific disclaimers, set forth at www.vishay.com/doc?91000 VBUS54DD-HS4 vishay semiconductors 4-line bus-port esd-protection note ? ratings at 25 c, ambient temperature unless otherwise specified. application note with the VBUS54DD-HS4 a double, high speed usb-port or up to 4 other high speed signal or data lines can be protected against transient voltage signals. negative transients will be clamped close belo w the ground level while positive transients w ill be clamped close above the working ra nge. the high speed data lines, d 1 +, d 2 +, d 1 - and d 2 -, are connected to pin 1, 3, 4, and 5, pin 2 or 6 are connected to ground. as long as the signal voltag e on the data lines is between the ground- and the break down level, the low input capacitance of eac h channel offers a very high isolation to ground and to the other data lines. but a s soon as any transient signal exceeds this working range, the vbus054dd-hs4 clamps the transient to ground or to the avalanche break down voltage level. typical characteristics (t amb = 25 c, unless otherwise specified) fig. 1 - 8/20 s peak pulse current wave form acc. iec 61000-4-5 fig. 2 - esd discharge current wave form acc. iec 61000-4-2 (330 ? /150 pf) electrical characteristics VBUS54DD-HS4 (pin 1, 3, 4 or 5 to pin 2 or 6) parameter test conditions/re marks symbol min. typ. max. unit protection paths number of lin es which can be protected n channel --4lines reverse stand off voltage at i r = 0.1 a v rwm 5.5 - - v reverse current at v in = v rwm = 5.5 v i r - < 0.01 0.1 a reverse breakdown voltage at i r = 1 ma v br 6.9 8 8.7 v reverse clamping voltage at i pp = 3 a; acc. iec 610000-4-5 v c -1619v forward clamping voltage at i f = 3 a; acc. iec 610000-4-5 v f -3.54.5v capacitance v in = 0 v; any other i/o pin at 3.3 v c d -0.81pf v in = 2.5 v; any other i/o pin at 3.3 v - 0.5 0.8 pf 20897-1 1 5 4 2 3 6 t w i n u s b - p o r t d 2+ v bus gnd r e c e i v e r ic d 2- d 1+ d 1- 0 % 20 % 40 % 60 % 80 % 100 % 010203040 time (s) i ppm 20 s to 50 % 8 s to 100 % 20548 0 % 20 % 40 % 60 % 80 % 100 % 120 % - 10 0 10 20 30 40 50 60 70 80 90 100 time (ns) discharge current i esd rise time = 0.7 ns to 1 ns 53 % 27 % 20557
document number: 83384 for technical questions, contact: esdprotection@vishay.com www.vishay.com rev. 1.0, 18-apr-11 3 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 VBUS54DD-HS4 4-line bus-port esd-protection vishay semiconductors fig. 3 - typical capacitance c d vs. reverse voltage v r fig. 4 - typical forward current i f vs. forward voltage v f fig. 5 - typical reverse voltage v r vs. reverse current i r fig. 6 - typical peak clamping voltage v c vs. peak pulse current i pp fig. 7 - typical clampi ng performanc e at + 8 kv contact discharge (acc. iec 61000-4-2) fig. 8 - typical clamping performance at - 8 kv contact discharge (acc. iec 61000-4-2) 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 v r (v) c d (pf) 0123456 f = 1 mhz pin 1, 3, 4 or 5 to pin 2 and 6 (one of pin 1, 3, 4 or 5 connected to 3.3 v) 0.001 0.01 0.1 1 10 100 0.5 0.6 0.7 0.8 0.9 1.0 1.1 v f (v) i f (ma) pin 2 and 6 to pin 1, 3, 4, or 5 0 1 2 3 4 5 6 7 8 9 0.01 0.1 1 10 1 10 2 10 3 10 4 i r (a) v r (v) pin 1, 3, 4 or 5 to pin 2 and 6 i pp (a) v c (v) - 5 0 5 10 15 20 01 2 3 4 measured acc. iec 61000-4-5 (8/20s - wave form) v c pin 1, 3, 4 or 5 to pin 2 and 6 - 10 0 10 2030405060708090 t (ns) v c-esd (v) - 20 0 20 40 60 80 100 120 acc. iec 61000-4-2 + 8 kv contact discharge pin 1, 3, 4 or 5 to pin 2 and 6 - 100 102030405060708090 t (ns) v c-esd (v) - 20 0 20 40 60 80 100 120 140 160 180 acc. iec 61000-4-2 - 8 kv contact discharge pin 1, 3, 4 or 5 to pin 2 and 6
www.vishay.com for technical questions, contact: esdprotection@vishay.com document number: 83384 4 rev. 1.0, 18-apr-11 this document is subject to change without notice. the products described herein and this document ar e subject to specific disclaimers, set forth at www.vishay.com/doc?91000 VBUS54DD-HS4 vishay semiconductors 4-line bus-port esd-protection package dimensions in millimeters (inches): llp1010-6m solder resist mask solder pad 0.125 (0.005) ref. 0.03 (0.001) 0 (0.000) pin 1 marking 0.4 (0.016) 0.33 (0.013) 0.35 (0.014) bsc 0.7 (0.028) ref. 0.22 (0.009) exp. dap 0.2 (0.008) 0.1 (0.004) 0.5 (0.020) exp. dap 0.25 (0.010) 0.15 (0.006) 1.05 (0.041) 0.95 (0.037) 1.05 (0.041) 0.95 (0.037) soldermask opening 0.03 measured middle of the package 0.05 (0.002) 0.175 (0.007) 0.35 (0.014) 0.7 (0.028) 0.35 (0.014) 0.3 (0.012) 0.22 (0.009) 0.5 (0.020) foot print recommendation: 20899 document no.:s8-v-3906.04-004 (4) rev. 4 - date: 09. sep. 2008 created - date: 17.july.2007
document number: 91 000 www.vishay.com revision: 11-mar-11 1 disclaimer legal disclaimer notice vishay all product, product specifications and data ar e subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectivel y, vishay), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicab le law, vishay disc laims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, incl uding without limitation specia l, consequential or incidental dama ges, and (iii) any and all impl ied warranties, including warran ties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of pro ducts for certain types of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in gene ric applications. such statements are not binding statements about the suitability of products for a partic ular application. it is the customers responsibility to validate that a particu lar product with the properties described in th e product specification is su itable for use in a particul ar application. parameters provided in datasheets an d/or specifications may vary in different applications and perfo rmance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vishays term s and conditions of purchase, including but not limited to the warranty expressed therein. except as expressly indicated in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vishay product co uld result in person al injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk and agr ee to fully indemnify and hold vishay and it s distributors harmless from and against an y and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that vis hay or its distributor was negligent regarding the design or manufact ure of the part. please contact authorized vishay personnel t o obtain written terms and conditions regarding products designed fo r such applications. no license, express or implied, by estoppel or otherwise, to any intelle ctual property rights is gran ted by this document or by any conduct of vishay. product names and markings noted herein may be trademarks of their respective owners.
|
